search

Lenze MC Series dynamic braking and form C relay Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Lenze MC Series dynamic braking and form C relay herunter. Lenze MC Series dynamic braking and form C relay User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 2
  • Inhaltsverzeichnis
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Lenze Americas • 630 Douglas Street • Uxbridge, MA 01569 • USA
Sales: (800) 217-9100 • Service: (508) 278-9100 • www.lenzeamericas.com
Lenze Americas • 630 Douglas Street • Uxbridge, MA 01569 • USA
Sales: (800) 217-9100 • Service: (508) 278-9100 • www.lenzeamericas.com
MDB01B
13360127
MDB01B
13360127
MC SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY OPTION
INSTALLATION INSTRUCTIONS (Manual Number: MDB01B)
1.0 INSTRUCTIONS FOR KITS: DYNAMIC BRAKING: 842-001, 842-002, 842-005
ADDITIONAL RELAY: 843-001, 843-006
1.1 PARTS LIST
(1) Dynamic Braking Board (9935-XXX or 9956-XXX) or Additional Form C Relay Board (9934-XXX or 9956-XXX)
(1) 7/16" Nylon sleeve standoff
(2) Nylon "snap-in" standoff (7.5 Hp kits only) (1) 3/4” Nylon sleeve standoff
(1) Resistor assembly (if ordered; DB kits only) (1) Nylon shoulder washer
1.2 PROCEDURE
DANGER!
Hazard of electrical shock! Remove power from the drive and wait three minutes before attempting this procedure.
DC Bus capacitors retain charge after power is removed..
STOP!
The internal components of the MC Series drive can be damaged by electrostatic discharge (ESD)! Use an antistatic wrist strap with
the ground clip attached to the drive ground lug when attempting this procedure. Always place components on antistatic surfaces or in
antistatic bags when they are not being handled during this procedure.
Note
Refer to 1.4 Exploded View while performing this procedure. This view is from the right side of the drive. Be careful when removing and
installing boards, as there are many pins that can be easily bent.
1. With drive cover removed, remove the keypad assembly. On NEMA 1 units, this is done by prying one end of the bracket up and out. On NEMA 4 or 12 units,
remove the screws that hold the bracket in place. Then unplug the keypad ribbon cable from the Main Control Board (9933A-XXX or 9019-XXX).
2. Remove the Main Control Board by removing the four screws (one at each corner), and carefully lifting the board straight up and out.
Remove the 1-5/16” nylon sleeve standoff from the lower left-hand corner screw, and replace it with the 3/4” nylon sleeve standoff from the kit.
There is a 2 x 6 pin connector that connects the P3 plug on the Main Control Board to the P3 plug on the Power Board below. Leave this plugged into the P3 plug on
the Power Board.
3. Under the Main Control Board is the Driver Board (9926-XXX) which must be removed to install the DB Board or Relay Board. Remove the Driver Board by pinching
the flared top of each nylon standoff while gently lifting up on the board (leave the standoffs snapped into the Power Board underneath).
Note
On 7.5 Hp, 480 Vac drives only, remove and save the 2 x 6 pin connector that is plugged into PL2 on the Driver Board (another 2 x 6
connector may be included in the DB kit; only one is needed).
4. Slide the nylon shoulder washer through the 3/16” hole near the lower left-hand side of the DB Board or Relay Board, and slide the 7/16” nylon sleeve standoff onto
the shoulder washer from the bottom side of the board.
NOTE: On 9956-XXX boards (kits 842-005 and 843-006), install the two nylon "snap-in" standoffs into the holes near the DB1 and DB2 terminals.
5. Snap the DB Board or Relay Board into place where the old Driver Board was, onto the same nylon standoffs that held the Driver Board in place.
Make sure that the PL1 pin connector (and the P8 and P9 spade connectors on DB Boards) makes positive contact with their respective plugs.
For 9956-XXX board (kits 842-005 and 843-006): this board will also have a P11 connector on the bottom of the board.
Make sure that the P11 connector makes positive contact to the pins on the Power Board below. Install the 2 x 6 pin connector in PL2.
6. Re-install the Main Control Board. Make sure that the PL2 and P3 pin connectors make positive contact through the bottom of the Main Control Board.
7. Re-install the keypad assembly and drive cover.
1.3 WIRING AND PROGRAMMING
Refer to the appropriate diagram to the right for wiring.
To enable Dynamic Braking, set DYN BRAKE (parameter
14) to ON.
To enable the Additional Form C Relay, set TB-14 OUT
(parameter 52) to the desired status indication.
Refer to the drive's Installation and Operation Manual for
more info on programming.
For Kit 842-005: This Dynamic Braking board for 7.5 Hp, 480
Vac drives also contains the Additional Form C Relay option.
DB1 DB2
RED
WIRE
BLUE
WIRE
From Resistor Assembly
Dynamic Braking Board
19 20 21
YELLOW WIRE
To TB-14 on Main
Control Board
Relay
Board
0.5 - 5 HP @ 240 Vac
1 - 7.5 HP @ 480 Vac
1 - 5 HP @ 590 Vac
1 5/8" SCREW (TYPICAL 2 PLCS.)
2 5/8" SCREW (TYPICAL 2 PLCS.)
SHOULDER WASHER
(TYPICAL 4 PLCS.)
2 X 6 PIN CONNECTOR
SCREW (TYPICAL 2 PLCS.)
CAPTIVE LOCK WASHER (TYPICAL 2 PLCS.)
SMALL FLAT WASHER (TYPICAL 2 PLCS.)
METAL STANDOFF (TYPICAL 2 PLCS.)
LOCK WASHER (TYPICAL 2 PLCS.)
LARGE FLAT WASHER (TYPICAL 2 PLCS.)
2 X 6 PIN CONNECTOR
1 7/8" STANDOFF (TYPICAL 4 PLCS.)
SNAP-IN STANDOFF
(TYPICAL 2 PLCS.)
RED BLUE
RED BLUE
480 Vac & 590 Vac 240 Vac
RED BLUE
841-007, 841-008, 841-009, 841-010
Connect each Tab #1 together with screw provided (copy the
configuration of the #2 tabs), and move the BLUE wire to Tab #2.
480 Vac & 590 Vac 240 Vac
841-011
Connect each Tab #1 together with screw provided (copy the
configuration of the #2 tabs), and move the BLUE wire to Tab #2.
RED BLUE
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
1 2
P2
P3
BC
HEATSINK
PL1
P3
A
}
}
}
}
}
}
}
}
}
}
}
}
}
}
P3
1PL2
P
B
PL3
POWER BOARD
BRAKING / RELAY
CONTROL BOARD
BOARD
2.4 EXPLODED VIEW
Applies to kits: 842-006, 842-007
843-007, 843-008
Note
Dynamic Braking Board is shown for
illustration purposes. The Additional Form
C Relay Board is very similar and the
installation procedure is the same.
7.5 - 30 HP @ 240 Vac
10 - 60 HP @ 480 Vac
7.5 - 60 HP @ 590 Vac
2.5 RESISTOR CONFIGURATIONS
When the Dynamic Braking Kit is ordered separately from the MC Series drive, the resistor assembly will be shipped in the 480 Vac and 590 Vac
configuration. For 240 Vac units, the resistor configuration must be modified, as shown below, using the hardware included with the kit.
Note
If the Dynamic Braking option is ordered with the drive, the resistor assembly will be shipped in the proper configuration, and no
modification is required
Seitenansicht 0
1 2

Inhaltsverzeichnis

Seite 1 - CONTROL BOARD

Lenze Americas • 630 Douglas Street • Uxbridge, MA 01569 • USASales: (800) 217-9100 • Service: (508) 278-9100 • www.lenzeamericas.comLenze Americas •

Seite 2 - MAIN CONTROL BOARD

Lenze Americas • 630 Douglas Street • Uxbridge, MA 01569 • USASales: (800) 217-9100 • Service: (508) 278-9100 • www.lenzeamericas.comLenze Americas •

Kommentare zu diesen Handbüchern

Keine Kommentare
Verwandte Produkte und Handbücher für Hardware Lenze MC Series dynamic braking and form C relay
Hardware Lenze Drive Server Bus server S7 getting started Bedienungsanleitung   (63 Seiten)
Hardware Lenze EPM−H310 Bedienungsanleitung     (102 Seiten)
Hardware Lenze E94AxPExxxx Bedienungsanleitung   (976 Seiten)
Hardware Lenze ECSCx Axis cold plate Bedienungsanleitung     (208 Seiten)
Hardware Lenze MC Series remote keypad Bedienungsanleitung   (2 Seiten)
Hardware Lenze SL Bedienungsanleitung   (52 Seiten)
Hardware Lenze EVS9332xK Bedienungsanleitung   (467 Seiten)
Hardware Lenze EVF9333 Bedienungsanleitung     (324 Seiten)
Hardware Lenze 712 E.3B Bedienungsanleitung    (68 Seiten)
Hardware Lenze MC1000 Series Bedienungsanleitung   (84 Seiten)
Hardware Lenze EPM-H312 Bedienungsanleitung     (94 Seiten)
Hardware Lenze MC3000 Series Bedienungsanleitung   (84 Seiten)
Hardware Lenze 931ExK10 Bedienungsanleitung    (60 Seiten)
Hardware Lenze MCH Series Drives Bedienungsanleitung   (17 Seiten)
Hardware Lenze EVS9332xP Bedienungsanleitung   (334 Seiten)
Hardware Lenze ECSDExxx Bedienungsanleitung     (170 Seiten)
Hardware Lenze EVF9338 Bedienungsanleitung     (158 Seiten)
Hardware Lenze E931Ex Bedienungsanleitung   (47 Seiten)
Hardware Lenze EPM−H315 Bedienungsanleitung     (108 Seiten)
Hardware Lenze EVS9332xP Bedienungsanleitung   (445 Seiten)
  • Boss Industrial Penpower Bali Cut-to-Size Cctv camera pros Motec
  • Audiovox CD-Radios Kubota Nein Jonsered Kraftkettensägen Mean Well Netzteile Breville Kaffeemacher
  • Sony DSC-F55V HP ENVY Photo 7134 All-in-One Printer Bamix Gastro 350 Biostar NF4 AM2
  • Lg DX325 Bedienungsanleitung Pioneer AVIC-HD3 Bedienungsanleitung Lg BD630 Bedienungsanleitung Bryston 875Z Bedienungshandbuch Sony DPPA-BT1 Bedienungsanleitung