Lenze E94P PositionServo Modbus Bedienungsanleitung PDF herunterladen (Seite 30)

30P94MOD01C

Reference

NOTE:

In true Modbus, 3X and 4X Registers are numbered starting at 1. This is known as ‘one based’ addressing.

However, when transmitted to a slave over the serial link, the actual address transmitted is one less.

Some Modbus masters will allow for the ﬁrst register number to be 0. This is known as ‘zero based’

addressing. If this is the case, the Modbus register numbers listed in this manual must be offset by -1 to

properly program a master using ‘zero-based’ addressing.

Index

Name

Type

Format

EPM

Access

Description Range Unit RAM

Registers

32bit

Integer

Access

RAM

32bit

Float

Access

EPM

Reg Copy

32bit

Integer

Access

EPM

Reg Copy

32bit

Float

Access

RAM

16bit

Signed

Integer

EPM

INT16

1 VAR_IDSTRING N R Drive’s identiﬁcation string 3 515 1027 1539 2050 2306

2 VAR_NAME Y R/W Drive’s symbolic name 5 517 1029 1541 2051 2307

3 VAR_SERIAL_NUMBER R Drive’s serial number 7 519 1031 1543 2052 2308

4 VAR_MEM_INDEX R/W Position in RAM ﬁle (0 - 32767) 9 521 1033 1545 2053 2309

5 VAR_MEM_VALUE R/W Value to be read or written to the RAM ﬁle 11 523 1035 1547 2054 2310

6 VAR_MEM_INDEX_

INCREMENT

R/W Holds value the MEM_INDEX will modify once

the R/W operation is complete

13 525 1037 1549 2055 2311

7 VAR_VELOCITY_ACTUAL R Actual measured motor velocity

NOTE: Only applicable to MVOB drives with

Firmware 4.00 and higher.

15 527 1039 1551 2056 2312

8 VAR_RSVD_2 17 529 1041 1553 2057 2313

9 VAR_DFAULT R Drive Default Settings 19 531 1043 1555 2058 2314

10 VAR_M_ID mtr Y R/W* Motor ID 21 533 1045 1557 2059 2315

11 VAR_M_MODEL mtr Y R/W* Motor model 23 535 1047 1559 2060 2316

12 VAR_M_VENDOR mtr Y R/W* Motor vendor 25 537 1049 1561 2061 2317

13 VAR_M_ESET mtr Y R/W* Motor Feedback Resolver: ‘Positive for CW’

0 - none

1 - Positive for CW

0 - 1 27 539 1051 1563 2062 2318

14 VAR_M_HALLCODE mtr Y R/W* Hallcode index 0 - 5 29 541 1053 1565 2063 2319

15 VAR_M_HOFFSET mtr Y R/W* Reserved 31 543 1055 1567 2064 2320

16 VAR_M_ZOFFSET mtr Y R/W* Resolver Offset 0 - 360 33 545 1057 1569 2065 2321

17 VAR_M_ICTRL mtr Y R/W* Reserved 35 547 1059 1571 2066 2322

18 VAR_M_JM mtr Y R/W* Motor moment of inertia Jm 0 - 0.1 Kgm2 37 549 1061 1573 2067 2323

19 VAR_M_KE mtr Y R/W* Motor voltage or back EMF constant Ke 1 - 500 V/Krpm 39 551 1063 1575 2068 2324

20 VAR_M_KT mtr Y R/W* Motor torque or force constant Kt 0.01 - 10 Nm/A 41 553 1065 1577 2069 2325

21 VAR_M_LS mtr Y R/W* Motor phase-to-phase inductance Lm 0.1 - 500 mH 43 555 1067 1579 2070 2326

22 VAR_M_RS mtr Y R/W* Motor phase-to-phase resistance Rm 0.01 - 500 [Ohm] 45 557 1069 1581 2071 2327

23 VAR_M_MAXCURRENT mtr Y R/W* Motor’s max current(RMS) 0.5 - 50 [A]mp 47 559 1071 1583 2072 2328

24 VAR_M_MAXVELOCITY mtr Y R/W* Motor’s max velocity 500 - 20000 RPM 49 561 1073 1585 2073 2329

25 VAR_M_NPOLES mtr Y R/W* Motor’s poles number 2 - 200 51 563 1075 1587 2074 2330

26 VAR_M_ENCODER mtr Y R/W* Encoder resolution 256 - 65536

* 12/Npoles

PPR 53 565 1077 1589 2075 2331

27 VAR_M_TERMVOLTAGE mtr Y R/W* Nominal Motor’s terminal voltage 50 - 800 [V]olt 55 567 1079 1591 2076 2332

28 VAR_M_FEEDBACK mtr Y R/W* Feedback type

1 - Encoder; 2 - Resolver

1 - 2 57 569 1081 1593 2077 2333

29 VAR_ENABLE_SWITCH_

TYPE

W Y R/W Enable switch function

0 - inhibit only; 1 - Run

0 - 1 Bit 59 571 1083 1595 2078 2334

30 VAR_CURRENTLIMIT F Y R/W Current limit [A]mp 61 573 1085 1597 2079 2335

31 VAR_

PEAKCURRENTLIMIT16

F Y R/W Peak current limit for 16kHz operation [A]mp 63 575 1087 1599 2080 2336

32 VAR_PEAKCURRENTLIMIT F Y R/W Peak current limit for 8kHz operation [A]mp 65 577 1089 1601 2081 2337

33 VAR_PWMFREQUENCY W Y R/W PWM frequency selection

0 - 16kHz; 1 - 8kHz

0 - 1 67 579 1091 1603 2082 2338

* These are all R/W variables but they only become active after variable 247 is set.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 36 37 38

Kommentare zu diesen Handbüchern

Keine Kommentare

Lenze E94P PositionServo Modbus Bedienungsanleitung Seite 30

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Lenze E94P PositionServo Modbus