Lenze Global Drive PLC Developer Studio Bedienungsanleitung PDF herunterladen (Seite 92)

8.5 System error messages

Drive PLC

Appendix

8−12

DrivePLC DE 6.0

8.5.4 Cause & remedy

No. Display Meaning Cause Remedy

−−− −−− No error − −

061 CE0 Communication error

AIF moduleóBasic unit

Interference during transfer of control commands

via automation interface (AIF)

Plug in automation module firmly, bolt down, if

necessary

062 CE1 CAN1_IN communication error

CANx_IN receives faulty data or communication

interrupted

 Check wiring/cable

 Check transmitter

 If possible, increase monitoring time under

C0357/x

063 CE2 CAN2_IN communication error

064 CE3 CAN3_IN communication error

065 CE4 CAN BUS−OFF status

(too many faulty telegrams

received)

PLC has received too many faulty telegrams sent

via system bus and has disconnected itself from

the bus

 Check wiring/cable

 Check bus termination (if any)

 Check screen contact of the cables

 Check PE connection

 Check bus load

 Reduce baud rate (observe cable length)

066 CE5 CAN time−out

(gateway function)

For remote parameterisation via system bus

(C0370):

 Slave does not respond

 Communication monitoring time exceeded

 Check system bus wiring/cable

 Check system bus configuration

070 U15 Undervoltage of internal 15 V

voltage supply

Check voltage supply for Drive PLC

071 CCR Internal error The program sequence of the processor was

interfered

 Shield control and motor cables as necessary

 Check PE wiring and PE connections

072 PR1 Check sum error

in parameter set 1

CAUTION:

Lenze setting is loaded

automatically!

 Error while loading a parameter set

 Interruption of parameter set transfer via

keypad (e.g. by disconnection of the keypad)

 Set the desired parameters and save them

under C0003

 For PR0 the supply voltage must be switched

off additionally

 Check use of pointers

The saved parameters do not match the loaded

software version

Before an error can be acknowledged, the

parameter set must be manually saved under

C0003

074 PEr Program error Error detected in program  Check use of pointers

 Send controller with parameter set and PLC

program (on diskette) to Lenze

075 PR0 General error in parameter sets

CAUTION:

Lenze setting is loaded

automatically!

See Cause & Remedy, no. 072 (PR1)

076 PR5 Error while saving parameters Error while saving parameters in the fail−safe

memory area

Contact Lenze

079 PI Error during

parameter initialisation

 Error detected during parameter set transfer

between two controllers

 Parameter set does not match the PLC or

controller (e.g. data transfer from a

high−performance controller to a

lower−performance controller)

 Correct the parameter set

 Check code initialisation values

080 PR6 Too many user codes Reduce the number of user codes

x09 EEr External monitoring activated

via DCTRL

A digital signal assigned to the TRIP−SET function

has been activated (system block DCTRL is

integrated as of software version V8.0)

 Check external encoder

 Deactivate monitoring (C0581 = 3)

105 H05 Internal error (memory) Contact Lenze

108 H08 Extension board error

Extension board not connected correctly  Connect extension board properly

 Check connection plug EBóPLC

Extension board is not supported by PLC program  Adapt PLC program to extension board

 Use extension board which is supported by PLC

program.

122 CE11 Communication error

FIF−CAN1_IN

FIF−CANx_IN receives faulty data or

communication interrupted

 Check wiring/cable

 Check transmitter

 If possible, increase monitoring time under

C2457/x

123 CE12 Communication error

FIF−CAN2_IN

124 CE13 Communication error

FIF−CAN3_IN

1 2 ... 87 88 89 90 91 92 93 94 95 96 97 ... 128 129

Kommentare zu diesen Handbüchern

Keine Kommentare

Lenze Global Drive PLC Developer Studio Bedienungsanleitung Seite 92

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Lenze Global Drive PLC Developer Studio