Lenze EMF2112IB Bedienungsanleitung PDF herunterladen (Seite 39)

Parameter setting

6-17

 BA2112EN

Signal configuration C0005 Bit 15

(AIF-CTRL.B15)

Bit 14

(AIF-CTRL.B1

Bit 13

(AIF-CTRL.B13)

Bit 12

(AIF-CTRL.B12)

Bit 11

(AIF-CTRL.B7)

Bit 6

(AIF-CTRL.B5)

Bit 5

(AIF-CTRL.B4)

vector control 1xx3 / 2xx3 / 3xx3

/ 5xx3 / 10xx3

NSET- RFG- STOP

(RFG stop)

NSET- RFG- 0

(RFG ze ro)

Reserved DCTRL-PAR*1 DCTRL-PAR-

LOAD

NSET-TI*1 NSET-TI*2

vector control 4xx3 NSET- RFG- STOP

(RFG stop)

NSET- RFG- 0

(RFG ze ro)

Reserved DCTRL-PAR*1 DCTRL-PAR-

LOAD

NSET- JOG*1 NSET-JOG*2

vector control 6xx3 / 7xx3 / 8xx3

/ 9xx3

Reserved Reserved Reserved DCTRL-PAR*1 DCTRL-PAR-

LOAD

Reserved Re se rved

vector control 11xx3 Reserved Reserved Reserved Reserved Re se rve d Rese rved Re se rved

6.1.3.3 Status word

Bit Name Meaning

0 Readytoswitchon Controller status information

0 = Status lower than “READYTOSWITCHON“

1 = Status at least “SWITCHED ON“

1 Ready for operation Controller status information

0 = Status lower than “READY FOR OPERATION“

1 = Status at least “READY FOR OPERATION“

2 Operation enabled Controller status information

0 = Status lower than “OPERATION ENABLED“

1=Status“OPERATION ENABLED“

3 Fault Controller status information

0 = No fault (TRIP))

1 = Fault (TRIP) occured

4 Voltage inhibited Information about command “Voltage inhibit“

0 = Command active

1 = Command not active

5 Quick stop Information about command “QUICK STOP“

0 = Command active

1 = Command not active

6 Switch-on inhibit Controller status information

0 = Status not “SWITCH-ON INHIBIT“

1=Status“SWITCH-ON INHIBIT“

7 Wa r n i ng Collective warning

0=Nowarning

1=warning

8 Message Collective message. Automatic setting and resetting of pulse inhibit in the controller status ”OPERATION ENABLED”. Reasons for

this can be undervoltage or overvoltage as well as overcurrent (clamp).

0 = No message

1 = Message (IMP)

9 Re mote 82xx, 821x, 822x, 8200 vector: Bus access right depends on Lenze parameter ”Operating mode” (C0001)

0 = C0001

≠ 3

1 = C0001 = 3

93XX:

10 Setpoint reached Status of speed/frequency deviation

0=RFGon

≠ RF G off

1 = RFGon = RFGoff

11 Limit value Status of the DRIVECOM speed limitation

always 0

12 Re se rved 820X, 821X, 822X: Reserved

8200 vector, 93XX: Mapping to bit C0150.B14

13 Re se rved 820X, 821x, 822x: Reserved

8200 vector: Mapping to bit C0150.B15

93XX: Mapping to bit C0150.B3

14 Manufacturer 820X, 821x, 822x: I max (current limit reached)

0 = Current limit not reached

1 = Current limit exceeded

8200 vector, 93XX: Mapping to bit C0150.B2

15 Manufacturer 820X, 821x, 822x: Q min (f d < dQmin )

0 = Q min not active

1=Qminactive

8200 vector, 93XX: Mapping to bit C0150.B5

Show/Hide Bookmarks

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 52 53

Kommentare zu diesen Handbüchern

Keine Kommentare

Lenze EMF2112IB Bedienungsanleitung Seite 39

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Lenze EMF2112IB