Lenze EPM−T9XX Modular system Bedienungsanleitung Seite 71
- Seite / 544
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4×analog input
4
The modular system
4.14
L
4.14−3
EDSPM−TXXX−9.0−11/2009
( Stop!
The module will be destroyed if the connected signals or encoders
do not match the set measuring range:
l Max. 15 V input voltage in the voltage measuring range.
l No input voltage in the resistance measuring range.
l When the measuring range is changed, only assign the inputs
after the first gateway initialisation has been completed:
– During initialisation, the previous settings are still active.
Unsuitable input circuits may destroy the modules. Changes
will only become effective and permanently saved after
initialisation.
Two−wire connection Four−wire connection
2
1
3
5
7
9
10
4
6
8
J
.
D
A
µP
MUX
PES
PES
PES
PES
PES
PES
PES
PES
D
A
µP
MUX
9
10
+U
+U
-U
-U
I
I
I
I
8
7
6
5
4
3
2
1
J
1
0
PES
PES
.
epm−t036 epm−t033
Fig. 4.14−3 Sensor connection
Analog input E.0
Analog input E.2
Connection to backplane bus
PES HF shield termination through large−surface connection to PE
Sensor:
Voltage or current source
Thermal element
Resistor
J
Resistor, temperature−dependent
l
Short−circuit unused inputs (connect positive and negative terminals) or
deactivate them by setting parameters.
l The module does not provide any auxiliary supply for sensors / actuators.
For information on how to connect an auxiliary supply, please see the
documentation for the sensors / actuators.
Connection
- I/O−System IP20 1
- Contents 10
- 1 Preface 11
- 1.1 The I/O system IP20 13
- How to use this System Manual 16
- Document history 17
- 1.2.3 Document history 17
- 1.3 Legal regulations 19
- Legal regulations 20
- Safety instructions 21
- Technical data 25
- The modular system 100
- The compact system 113
- EPM-T831 1A.10 127
- EPM-T833 1A.10 135
- 02413567 143
- Mechanical installation 147
- Electrical installation 155
- 8.1 Via system bus (CAN) 171
- 8.2 Network management (NMT) 173
- Network management (NMT) 174
- 8.3 Transmitting process data 175
- Transmitting process data 176
- PDO1-TX PDO1-RX 178
- 2. 3. 4 178
- Transmitting parameter data 188
- Telegram structure 188
- Identifier = 1538 190
- Identifier = 1410 190
- 8.6 Node Guarding 195
- Node Guarding 196
- 8.7 Heartbeat 197
- Heartbeat 198
- 8.8 Reset node 199
- 8.9 Monitoring 201
- Monitoring 202
- Digital output monitoring 202
- 8.10 Diagnostics 205
- Diagnostics 206
- Emergency telegram 206
- 8.10.1 Emergency telegram 206
- Status of the digital outputs 208
- Via the index I6401 209
- Via the index I6411 209
- Network via CANopen 211
- Networking via PROFIBUS−DP 255
- Commissioning 283
- 12.1 Important notes 295
- Parameterising analog modules 300
- Parameter data 300
- Diagnostic data 304
- 12.3.2 Diagnostic data 304
- 12.3−11 309
- 12.3−12 310
- 12.3−13 311
- 12.3−16 314
- 12.3−17 315
- 12.3−18 316
- Input data / output data 325
- 2 x 32 bit counter (mode 0) 326
- Encoder (modes 1, 3, and 5) 328
- Counter 0 332
- Counter 1 332
- 12.4−13 333
- 12.4−14 334
- 12.4−15 335
- 12.4−16 336
- 12.4−17 337
- 12.4−18 338
- 12.4−19 339
- 12.4−20 340
- 12.4−21 341
- 12.4−22 342
- 12.4−23 343
- 12.4−24 344
- 12.4−25 345
- 12.4−26 346
- 12.4−27 347
- 12.4−28 348
- 12.4−30 350
- 12.4−31 351
- 12.4−32 352
- 12.4−33 353
- 12.4−34 354
- 12.4−35 355
- 12.4−36 356
- 12.4−37 357
- 12.4−38 358
- 12.4−39 359
- 12.4−40 360
- 12.4−41 361
- 12.4−42 362
- 12.4−43 363
- 12.4−44 364
- 12.4−45 365
- 12.4−46 366
- 12.4−47 367
- 12.4−48 368
- 12.4−49 369
- 12.4−50 370
- 12.4−51 371
- 12.4−52 372
- 12.4−53 373
- 12.4−54 374
- 12.4−55 375
- 12.4−56 376
- Parameterising SSI interface 379
- EDSPM−TXXX−9.0−11/2009 384
- 12.5−11 387
- Encoder (mode 0) 395
- 12.6.3 Encoder (mode 0) 395
- 32 bit counter (mode 1) 397
- 12.6−10 400
- 12.6−11 401
- 12.6−12 402
- 12.6−13 403
- Measuring the period (mode 4) 404
- 12.6−15 405
- 12.8 Loading default setting 409
- · Example: 413
- 13.1−11 423
- 13.1−12 424
- 13.1−14 426
- 13.1−16 428
- 13.1−17 429
- 13.1−18 430
- Gateway Counter 438
- Data to module 438
- Data from module 438
- In3/In6 (DIR) 446
- 13.2−13 447
- 13.2−14 448
- 13.2−15 449
- Counter access 450
- 13.2−17 451
- 13.2−18 452
- 13.2−19 453
- 13.2−20 454
- 13.2−21 455
- 13.2−22 456
- 13.2−23 457
- 13.2−24 458
- 13.2−25 459
- 13.2−26 460
- 13.2−27 461
- 13.2−29 463
- 13.2−30 464
- 13.2−31 465
- 13.2−32 466
- 13.2−33 467
- 13.2−34 468
- 13.2−36 470
- 13.2−37 471
- 13.2−38 472
- 13.2−40 474
- In3/In6 (B) 475
- 13.2−42 476
- 13.2−43 477
- 13.2−44 478
- 13.2−46 480
- 13.2−47 481
- 13.2−48 482
- 13.2−49 483
- 13.2−50 484
- 13.2−52 486
- 13.2−54 488
- 13.2−55 489
- 13.3.1 Parameter data 491
- Gateway SSI-Interface 493
- 13.4.1 Parameter data 495
- Gateway Counter/Dig In 496
- 13.4.3 Encoder (mode 0) 498
- Signal characteristic 503
- 13.4−10 504
- 13.4−11 505
- 13.4−12 506
- 13.4−14 508
- 14.1 Fault messages 511
- Appendix 513
- 10987654321 544
Verwandte Produkte und Handbücher für Hardware Lenze EPM−T9XX Modular system
Hardware Lenze EMZ9374IB Bedienungsanleitung
(122 Seiten)
(122 Seiten)
Hardware Lenze EZN3x0060H054 Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Hardware Lenze EPM-H521 Bedienungsanleitung
(136 Seiten)
(136 Seiten)
Hardware Lenze MC−xxx Card Bedienungsanleitung
(46 Seiten)
(46 Seiten)
Hardware Lenze EWS1001 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Lenze EWS1003 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Hardware Lenze E93ZWLX Bedienungsanleitung
(77 Seiten)
(77 Seiten)
Hardware Lenze EMZ2221IB Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Hardware Lenze E82ZMBRB Bedienungsanleitung
(58 Seiten)
(58 Seiten)
Hardware Lenze ECSCMxxx Bedienungsanleitung
(375 Seiten)
(375 Seiten)
Hardware Lenze ECSZZxxxxxx Bedienungsanleitung
(68 Seiten)
(68 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern