Lenze EMF2113IB Bedienungsanleitung PDF herunterladen (Seite 48)

Commissioning

Prepare controller for INTERBUS operation

Feldbus-Baugruppe 2113 INTERBUS

7.5

7.5.6

7.5-6

EDSIBS-1.0-06/2003

7.5.6 Prepare controller for INTERBUS operation

Preparation Notes

1. L-C0001 (o perat i ng mode):

Change value from “0” to “3”

For this use

• the 8201BB for 82XX and

• the keypad for 8200 vector

Alternative

Direct access to the code via INTERBUS.

Example

Set code L-C0001 t o “3” (PCP write):

– Index: 5FFE

hex

(= 5FFF

hex

− (L- C0001)

hex

)

– Subindex: 0

– Value: 30000

dec

à For conversion formula and parameter value range see ^ 7.6-47

8200 vector (up to S W version 1.1)

à C0410/y (y = 1...16) must be assigne d to the AIF control word (A IF-CTRL)

i.e. C0410/1 = 10, C0410/2 = 11 .... C0410/16 = 25 (se e Operating

Instructions f o r 8200 vector).

2. Terminal 28 (controller

enable) must be HIGH during

INTERBUS operation.

Terminal 28 is always

active!

Otherwise, the controller cannot be enabled by the INTERBUS (DRIVECOM

controller status ”OPERATION ENABLED”, see Operating Instructions for the

controller).

821X, 8200vector und 822X

With these controllers the QSP function is always active. If QSP is assigned to an

input terminal (default setting: not assigned), this terminal must be at HIGH level

during INTERBUS operation (see the corresponding Operating Instructions).

The controller is now ready to accept process and parameter data from the INTERBUS.

Preparation Notes

1. L-C0005: Se t “xxx3”. Use t he 9371BB ke ypad

Alternative:

Direct access to the code via INTERBUS.

For the first commissioning yo u should select the signal configuration 1013 (speed

control).

Example

Set code L-C0005 to “1013” (PCP write):

– Index: 5FFA

hex

(5FFF

hex

− (L- C0005)

hex

)

– Subindex: 0

– Value: 10130000

dec

à For conversion formula and parameter value range see ^ 7.6-47

2. L-C0142 (autostart lock):

Set “0”.

Only necessary with DRIVECOM control

3. Terminal 28 (controller

enable) must be HIGH during

INTERBUS operation.

Terminal 28 is always

active!

Otherwise, the controller cannot be enabled by the INTERBUS (DRIVECOM

controller status ”OPERATION ENABLED”, see Operating Instructions for 93XX).

à Wit h the signal configuration L-C0005=1013, the functi on QSP (quick stop) and

the CW/CCW changeover are assigned to the digital input terminals E1 and E2

and thus they are always active. For INTERBUS operation E1 must be set to

HIGH level (see Operating Instructions 93XX).

à Wit h t he signal configuration L-C0005=xx13, terminal A1 is switched as

voltage output. Thus, only the following terminals can be connected via cables:

– X5.A1 with X5.28 (ctrl. enable)

– X5.A1 with X5.E1 (CW/QSP)

The controller is now ready to accept process and parameter data from the INTERBUS.

82XX / 8200 vector

93XX controllers

Show/Hide Bookmarks

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 118 119

Kommentare zu diesen Handbüchern

Keine Kommentare

Lenze EMF2113IB Bedienungsanleitung Seite 48

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Lenze EMF2113IB