Lenze 9400 Bedienungsanleitung PDF herunterladen (Seite 937)

Lenze · Servo-Inverter 9400 HighLine · Reference manual · DMS 10.0 EN · 11/2013 · TD05/06 937

Index

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

D

D component position controller (C02555) 856

Data type 714

Date 840, 841

DC brake

Activat. by quick stop (C00976)

828

Current (C00974) 828

Current for quick stop (C00975) 828

DC bus overvoltage (error message) 650

DC bus undervoltage (error message) 650

DC-bus capacitor

Thermal detector is defect (error message)

644

DC-bus voltage (C00053) 736

DC-injection braking 212, 392

Decel. time - quick stop (C00105) 742

Decel. time lim. speed (C02712) 886

Deceleration has been limited (error message) 700

Deceleration time (C02775) 893

Deceleration time for stop (C02610) 868

Delay lim. speed (C02710) 886

Delay time for fan start (C01201) 838

Depth of current setpoint filter (C00272) 762

Device command status (C00003) 724

Device command transferred incorrectly (error message) 647

Device commands (C00002) 720

Device commands, commands

See device commands, C2 (device command), C3 (device

command status)

42

Device name (C00199) 756

Device state (C00183) 755

Device states 97

Device type (I-1000) 341

Device utilisation (Ixt) (C00064) 738

Device utilisation Ixt > 100 % (error message) 645

Device utilisation Ixt > C00123 (error message) 645

DFIN (MXI1)

Signal error enable/lamp control (error message)

683

Supply cannot be corrected anymore (error message) 684

Track error A-/A (error message) 683

Track error B-/B (error message) 683

Track error Z-/Z (error message) 683

DFIN (MXI2)

Signal error enable/lamp control (error message)

691

Supply cannot be corrected anymore (error message) 691

Track error A-/A (error message) 690

Track error B-/B (error message) 690

Track error Z-/Z (error message) 690

DFOUT (MXI1)

Maximum frequency reached (error message)

684

DFOUT (MXI2)

Maximum frequency reached (error message)

691

DI_bErrors (C02548) 855

DI_dnState (C02547) 854

Diagnostics X6

Change baud rate (C01903)

846

Curr. baud rate (C01905) 846

Max. baud rate (C01902) 846

Dig. input x

Terminal polarity (C00114)

743

Dig. output x

Terminal polarity (C00118)

743

Digital inputs 279

Delay time (C02830) 900

Digital outputs 281

DIP switches of the memory module 296

direct control 523

Disconnection in the case of par. storage (error message) 678

Distribution cam data memory 554

Division by zero (error message) 637

Document history 11

Double motor 225, 551

Drive interface 28

Signals (C02549) 855

DRIVE-ERROR LED 98, 599

DRIVE-READY LED 98, 599

Dual motor temperature (C01200) 838

Dynamic of resolver evaluation (C00417) 786

Dynamics of the actual value detection 149

E

Earth fault detected (error message) 651

Elapsed-hour meter (C00178) 754

Electronic cam 552

Electronic nameplate

Checksum error (error message)

630

Communication error (error message) 630

Data are incompatible (error message) 647

Data loaded (error message) 657

Data outside the parameter limits (error message) 659

Encoder protocol unknown (error message) 657

Encoder signal unknown (error message) 657

Not found (error message) 657

Electronic nameplate status (C2858) 902

E-mail to Lenze 952

Emergency telegram 338

EN 60204-1 366

EN 954 366

ENC_bError (C02765) 891

Encoder

Open circuit (error message)

653

Encoder - angular drift monitoring 264

Encoder evaluation 236

Dig. signals (C02579) 861

Encoder monitoring

Pulse deviation detected (error message)

660

Encoder position (C02762) 890

Encoder revolution (C02763) 890

Encoder signal X8 260

1 2 ... 932 933 934 935 936 937 938 939 940 941 942 ... 953 954

Kommentare zu diesen Handbüchern

Keine Kommentare