Lenze ETC Motion Control Bedienungsanleitung PDF herunterladen (Seite 246)

Interface PLC <˘> NC operating system

Definitions

Data block 1

5.1

5.1.2

246

EDSTCXN EN 2.0

DirectionNameData word

033.00 db1_sps2nc_hfkt_quitt_bit PLC ® NC

035.00 db1_sps2nc_extsync_enable_bit PLC ® NC

035.08 db1_sps2nc_programmhalt_aktiv_bit PLC ® NC

036.00 – 037.15

038.00 – 039.15

db1_sps2nc_qin_mask_aw

db1_sps2nc_qout_mask_aw

PLC ® NC

042.00 – 043.15

044.00 – 045.15

db1_sps2nc_qin_offset_ab

db1_sps2nc_qout_offset_ab

PLC ® NC

080.00 – 080.15

081.00 – 081.15

082.00 – 082.15

083.00 – 083.15

db1_sps2nc_spsoverride_allg_w

db1_sps2nc_spsoverride_spindel_w

db1_sps2nc_spsoverride_ozillation_w

db1_sps2nc_spsoverride_sps_w

PLC ® NC

084.00 – 091.15 db1_sps2nc_verfahr_ab PLC ® NC

128.00

128.01

db1_nc2sps_betriebsbereit_1_bit

db1_nc2sps_betriebsbereit_2_bit

PLC ¬ NC

129.00 – 129.15 db1_nc2sps_referenzpunkt_w PLC ¬ NC

130.00 – 131.15 db1_nc2sps_referenzfahrt_laeuft_w PLC ¬ NC

131.00 – 131.15 db1_nc2sps_betriebsart_w PLC ¬ NC

132.00

132.02

132.03

132.04

db1_nc2sps_nc_programm_laeuft_bit

db1_nc2sps_satzvorlauf_aktiv_bit

db1_nc2sps_einzelsatz_laeuft_bit

db1_nc2sps_unterbrechen_aktiv_bit

PLC ¬ NC

132.08 db1_nc2sps_alle_achsen_stehen_bit PLC ¬ NC

133.00 – 133.07 db1_nc2sps_wahlweise_halt_b PLC ¬ NC

133.08 – 133.15 db1_nc2sps_programmstartzaehler_b PLC ¬ NC

134.00 – 134.15 db1_nc2sps_achse_faehrt_w PLC ¬ NC

135.00 – 135.15 db1_nc2sps_modal_am_ziel_w PLC ¬ NC

137.00 – 137.07 db1_nc2sps_programmstart_b PLC ¬ NC

137.08 – 137.15 db1_nc2sps_einzel_folgesatz_bit PLC ¬ NC

138.00 – 138.15

139.00 – 139.15

db1_nc2sps_canmodul_vorhanden_w

db1_nc2sps_can_status_w

PLC ¬ NC

142.00 db1_nc2sps_programmstop_b PLC ¬ NC

144.00 db1_nc2sps_vorschub_halt_b PLC ¬ NC

150.00

151.00 – 151.15

db1_nc2sps_mfkt_strobe_bit

db1_nc2sps_mfkt_w

PLC ¬ NC

159.00

160.00 – 160.15

db1_nc2sps_hfkt_strobe_bit

db1_nc2sps_hfkt_w

PLC ¬ NC

177.00 – 177.15 db1_nc2sps_refpunkt_angefahren_w PLC ¬ NC

178.00 – 178.15

179.00 – 179.15

180.00 – 180.15

181.00 – 181.15

db1_nc2sps_endschalter_plus_w

db1_nc2sps_endschalter_minus_w

db1_nc2sps_referenznocken_w

db1_nc2sps_reserveeingang_w

PLC ¬ NC

182.00 – 182.15

183.00 – 183.15

184.00 – 184.15

185.00 – 185.15

db1_nc2sps_slave_endschalter_plus_w

db1_nc2sps_slave_endschalter_minus_w

db1_nc2sps_slave_referenznocken_w

db1_nc2sps_slave_reserveeingang_w

PLC ¬ NC

192.00 – 199.15 db1_nc2sps_copmodul_vorhanden_aw PLC ¬ NC

200.00 – 200.15

201.00 – 201.15

202.00 – 202.15

203.00 – 203.15

db1_nc2sps_spsoverride_allg_w

db1_nc2sps_spsoverride_spindel_w

db1_nc2sps_spsoverride_ozillation_w

db1_nc2sps_spsoverride_sps_w

PLC ¬ NC

204.00 – 211.15

db1_nc2sps_verfahr_ab

PLC ¬ HMI

212.00 – 219.15 db1_nc2sps_mmi_tasten_aw PLC ¬ HMI

All of the areas that are not listed explicitly are reserved.

1 2 ... 241 242 243 244 245 246 247 248 249 250 251 ... 427 428

Lenze ETC Motion Control Bedienungsanleitung Seite 246

Kommentare zu diesen Handbüchern

Lenze ETC Motion Control Bedienungsanleitung Seite 246

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Lenze ETC Motion Control