Lenze ETC Motion Control Bedienungsanleitung PDF herunterladen (Seite 423)

Contents i

423

EDSTCXN EN 2.0

− READ_TOOLDATA, 367

− READBLOCKV24, 379

− ReadCanMsg, 412

− READV24, 379

− RTC_GetTime_DT, 417

− RTC_SetTime_DT, 417

− SAVE, 376 , 383

− SAVE_PARAM, 368 , 376

− SetCurrentPath, 384

− SETINPUT_BIT, 368

− SETINPUT_WORD, 369

− SETLANGUAGE, 372

− SINGLEBLOCK, 369

− SPSERROR, 370

− STRTOF, 372

− STRTOL10, 372

− SYSCLOSEFILE, 385

− SYSDISKFORMAT, 387

− SYSDISKINFO, 389

− SYSERROR, 373

− SYSFIRSTFILE, 388

− SYSNEXTFILE, 388

− SYSOPENFILE, 384

− SYSREADFILE, 385

− SYSREADLINE, 386

− SYSREMOVEFILE, 387

− SYSWRITEFILE, 386

− TRACE, 373

− V24 function constants, 382

− WordWrap, 374

− WRITE_PARAM_DINT, 374

− WRITE_PARAM_INT, 374

− WRITE_PARAM_LREAL, 375

− WRITE_PARAM_REAL, 375

− WRITE_SYSPARAM, 375

− WRITEBLOCKV24, 379

− WriteCanMsg, 413

− WRITEV24, 380

G function

− Individual descriptions, 94

− overview, 91

G preparatory function, 89

G−function, basics, 45

G00 Point−to−point positioning, high rate, 94

G01 Linear interpolation, 97

G02 Circular interpolation, 99

G04 Dwell time, 102

G05 Spline interpolation, 103

G06 Polynomial interpolation, 105

G100 Polar coordinates: linear interpolation, high rate,

126

G101 Polar coordinates: linear interpolation, 127

G102/G103 Polar coordinates: circular interpolation, 128

G110 Polar coordinates: accept center, 129

G111 Polar coordinates: center programming, 129

G112 Tangential correction on, 130

G113 Tangential correction off, 131

G114 6−axes transformation, 131

G115 Convex surface transformation, 132

G116 Rotation axes transformation, 133

G120 Abs. coordinate shift via modal offset, 134

G121 Programming the modal offset, 135

G122 Configuring the effect of the traverse keys, 136

G125 Parameter field comparison, 137

G130 Parameter field comparison, 138

G131 Delete modal comparative operation, 140

G132 Inhibit modal program branching, 140

G133 Enable modal program branching, 140

G134 Parameter field comparison, 141

G140/G141/G142 Noncircular grinding, 142

G143 Parameters of grinding phases during noncircular

grinding, 144

G144/G145 Programming a correction table during

noncircular grinding, 145

G150 Q−Bit comparison, 146

G151 Q−Bit comparison, 148

G152 Q−Bit comparison, 149

G153 Wait for the termination of a channel 1, 150

G158/G159 Intermittent operation, 151

G16 Selection of the principal and secondary axes, 107

G161 Accept actual position, 152

G162 Define axis group, 153

G17, G18, G19 Plane selection, 108

G175 Axis replacement, 154

G180 Modal travel , 155

G181 Modal travel , 156

G187 Handwheel, 156

G193 Set absolute zero point, 157

G194 Program an add. basic offset, 157

1 2 ... 418 419 420 421 422 423 424 425 426 427 428

Kommentare zu diesen Handbüchern

ama 11 Jan 2025 | 19:35:39

rasha

Lenze ETC Motion Control Bedienungsanleitung Seite 423

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Lenze ETC Motion Control